Purpose   • Technical data   • Installation and service   • Documentation   • Software

INTERFACE TRANSFORMERS ARE INITIATIVE-M

The converter of interfaces is proactive execution 1     

Initiative interface converter - M       Перетворювач інтерфейсів RS232/BELL202       Перетворювач інтерфейсів RS232/RS485       Перетворювач інтерфейсів RS232/RS232 ізолюючий       Перетворювач інтерфейсів RS232/ML       Контролер-перетворювач інтерфейсів       Перетворювач інтерфейсів SH/RS232       Перетворювач Bell 202/ТОК 4 - 20 mA       Концентратор RS232 ізолюючий       Перетворювач інтерфейсів USB/PLI       Перетворювач інтерфейсів USB/BEL202       Перетворювач інтерфейсів RS485/PLI       Перетворювач інтерфейсів RS232/PLI ізолюючий       Адаптер BELL202       Перетворювач інтерфейсів RS485/BELL202      

PURPOSE
( full specifications are in the manual for the device )

1. The proactive interface converter (equipped with a built-in GPRS modem) is designed for transmission daily/hourly reports from Gas consumption calculators via the Internet to the server of the user's dispatch service. The devices are equipped with one or two slots for installing Sim cards.
   Initiative interface converters provide the ability to transfer data from all objects simultaneously. This makes it possible to quickly receive data from a large number of calculators of gas metering units.
   The proactive converter automatically polls cost calculators and transmits the results calculations at specified user addresses at the set time. (The number of polls per day and the time of transmission of calculation results user defines independently).
  The Converter also provides traditional access to the Calculator upon proactive requests from dispatch programs survey and maintenance of Computers.
2. The proactive interface converter is not a measuring tool.
3. Operation of the converter is allowed at ambient air temperature from minus 40 to
plus 70 °C.
   P.S. - Attention! - If necessary, the user can independently configure the Interface Converter with the initiative program "VexnaServ.exe" in accordance with the recommendations of these programs during configuration.
    In order to set up data exchange between the Calculator and the Converter, the proactive interfaces must be set the address of the connected Computer VR-2 (Computer PC-B) and the Internet connection parameters of the correspondingly inserted SIM card ("www.kyivstar.net" - for Kyivstar, or "www.umc.ua" - for MTS, etc.).

TECHNICAL DATA

1. The mode of operation of the communication lines of the converter is half-duplex.
2. The proactive interface converter provides data exchange at speeds from  600 to 57600 bit/s.
3. The converter has galvanic isolation between Bell202 and RS232 interfaces.
4. The converter is powered by an external DC source
nominal voltage - 12 V (permissible - from 8 to 16 V);
   consumption current:
    - average current - 100 mA;
    - maximum - no more than 2.5 A;
    - power consumption - no more than 60 W.
5. The degree of protection of the converter housing from environmental influences is IP30 according to GOST 14254.
6. The dimensions of the converter do not exceed 160 x 100 x 60 mm.
7. The mass of the converter does not exceed - 0.25 kg.
8. The service life of the converter is 12 years.

INSTALLATION & SERVICE

1. The interface converter is proactive made in a plastic case with brackets for mounting on a DIN rail. At the same time, the converter must be protected from direct exposure to atmospheric precipitation.
2. The company provides 24-month warranty service for initiative interface converters and service throughout the service life.

DOCUMENTATION  (Manual)

The interface converter is proactive.
Initiative interface converter - M.

SOFTWARE

VexnaServ_vXX.zip – Setup and maintenance program "Interface converters are proactive” (VexnaServ_vXX.exe, where XX is the version number of the program that is inside the VexnaServ.zip archive) and other supporting programs.

manual.pdf - Instructions for the operation of the "HostWin" program in the presence of the "Initiative Interface Converter" as part of the FLOUTEC-TM measuring complex.

USB_Stm32_Driver.zip - The driver for connecting the "Initiative Interface Converter" via the USB interface